In the Linux kernel, the following vulnerability has been resolved:
spi: microchip-core-qspi: control built-in cs manually
The coreQSPI IP supports only a single chip select, which is
automagically operated by the hardware - set low when the transmit
buffer first gets written to and set high when the number of bytes
written to the TOTALBYTES field of the FRAMES register have been sent on
the bus. Additional devices must use GPIOs for their chip selects.
It was reported to me that if there are two devices attached to this
QSPI controller that the in-built chip select is set low while linux
tries to access the device attached to the GPIO.
This went undetected as the boards that connected multiple devices to
the SPI controller all exclusively used GPIOs for chip selects, not
relying on the built-in chip select at all. It turns out that this was
because the built-in chip select, when controlled automagically, is set
low when active and high when inactive, thereby ruling out its use for
active-high devices or devices that need to transmit with the chip
select disabled.
Modify the driver so that it controls chip select directly, retaining
the behaviour for mem_ops of setting the chip select active for the
entire duration of the transfer in the exec_op callback. For regular
transfers, implement the set_cs callback for the core to use.
As part of this, the existing setup callback, mchp_coreqspi_setup_op(),
is removed. Modifying the CLKIDLE field is not safe to do during
operation when there are multiple devices, so this code is removed
entirely. Setting the MASTER and ENABLE fields is something that can be
done once at probe, it doesn't need to be re-run for each device.
Instead the new setup callback sets the built-in chip select to its
inactive state for active-low devices, as the reset value of the chip
select in software controlled mode is low.
spi: microchip-core-qspi: control built-in cs manually
The coreQSPI IP supports only a single chip select, which is
automagically operated by the hardware - set low when the transmit
buffer first gets written to and set high when the number of bytes
written to the TOTALBYTES field of the FRAMES register have been sent on
the bus. Additional devices must use GPIOs for their chip selects.
It was reported to me that if there are two devices attached to this
QSPI controller that the in-built chip select is set low while linux
tries to access the device attached to the GPIO.
This went undetected as the boards that connected multiple devices to
the SPI controller all exclusively used GPIOs for chip selects, not
relying on the built-in chip select at all. It turns out that this was
because the built-in chip select, when controlled automagically, is set
low when active and high when inactive, thereby ruling out its use for
active-high devices or devices that need to transmit with the chip
select disabled.
Modify the driver so that it controls chip select directly, retaining
the behaviour for mem_ops of setting the chip select active for the
entire duration of the transfer in the exec_op callback. For regular
transfers, implement the set_cs callback for the core to use.
As part of this, the existing setup callback, mchp_coreqspi_setup_op(),
is removed. Modifying the CLKIDLE field is not safe to do during
operation when there are multiple devices, so this code is removed
entirely. Setting the MASTER and ENABLE fields is something that can be
done once at probe, it doesn't need to be re-run for each device.
Instead the new setup callback sets the built-in chip select to its
inactive state for active-low devices, as the reset value of the chip
select in software controlled mode is low.
Default status is the baseline for the product, each version can override it (e.g. patched versions marked unaffected).
| Vendor | Product | Default status | Versions | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Linux | Linux | unaffected |
|
||||||||||||||||||
| Linux | Linux | affected |
|
No data.
No data.
OpenCVE Enrichment is a feature of OpenCVE that uses AI to automatically link vendors and products to CVEs. Learn more on GitHub.
No data.
Advisories
No advisories yet.
Fixes
Solution
No solution given by the vendor.
Workaround
No workaround given by the vendor.
References
History
Thu, 28 May 2026 12:00:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Weaknesses | CWE-665 |
Thu, 28 May 2026 10:15:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | In the Linux kernel, the following vulnerability has been resolved: spi: microchip-core-qspi: control built-in cs manually The coreQSPI IP supports only a single chip select, which is automagically operated by the hardware - set low when the transmit buffer first gets written to and set high when the number of bytes written to the TOTALBYTES field of the FRAMES register have been sent on the bus. Additional devices must use GPIOs for their chip selects. It was reported to me that if there are two devices attached to this QSPI controller that the in-built chip select is set low while linux tries to access the device attached to the GPIO. This went undetected as the boards that connected multiple devices to the SPI controller all exclusively used GPIOs for chip selects, not relying on the built-in chip select at all. It turns out that this was because the built-in chip select, when controlled automagically, is set low when active and high when inactive, thereby ruling out its use for active-high devices or devices that need to transmit with the chip select disabled. Modify the driver so that it controls chip select directly, retaining the behaviour for mem_ops of setting the chip select active for the entire duration of the transfer in the exec_op callback. For regular transfers, implement the set_cs callback for the core to use. As part of this, the existing setup callback, mchp_coreqspi_setup_op(), is removed. Modifying the CLKIDLE field is not safe to do during operation when there are multiple devices, so this code is removed entirely. Setting the MASTER and ENABLE fields is something that can be done once at probe, it doesn't need to be re-run for each device. Instead the new setup callback sets the built-in chip select to its inactive state for active-low devices, as the reset value of the chip select in software controlled mode is low. | |
| Title | spi: microchip-core-qspi: control built-in cs manually | |
| First Time appeared |
Linux
Linux linux Kernel |
|
| CPEs | cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* | |
| Vendors & Products |
Linux
Linux linux Kernel |
|
| References |
|
Projects
Sign in to view the affected projects.
MITRE
Status: PUBLISHED
Assigner: Linux
Published:
Updated: 2026-05-28T09:36:04.805Z
Reserved: 2026-05-13T15:03:33.101Z
Link: CVE-2026-46148
Vulnrichment
No data.
NVD
Status : Received
Published: 2026-05-28T10:16:30.410
Modified: 2026-05-28T10:16:30.410
Link: CVE-2026-46148
Redhat
No data.
OpenCVE Enrichment
Updated: 2026-05-28T11:45:16Z
Weaknesses